50G2
Gears, friction wheels, gear shafts and other parts operating abrasion.
Classification
Chemical composition
| Standard | Fe, % | Si, % | Mn, % | Cr, % | Cu, % | Ni, % | P, % | C, % | S, % |
|---|---|---|---|---|---|---|---|---|---|
| Standard | Fe, % | Si, % | Mn, % | Cr, % | Cu, % | Ni, % | P, % | C, % | S, % |
| GOST 4543-71 | 96.31–97.97 | 0.17–0.37 | 1.4–1.8 | < 0.3 | < 0.3 | < 0.3 | < 0.035 | 0.46–0.55 | < 0.035 |
Information on suppliers
Physical characteristics
| Temperature, °C | $$E\cdot 10^{9}$$, $$MPa$$ | $$\alpha\cdot 10^{6}$$, $$K^{-1}$$ | $$\varkappa$$, $$\frac{W}{m\cdot K}$$ | $$\rho$$, $$\frac{kg}{m^3}$$ |
|---|---|---|---|---|
| Temperature, °C | $$E\cdot 10^{9}$$, $$MPa$$ | $$\alpha\cdot 10^{6}$$, $$K^{-1}$$ | $$\varkappa$$, $$\frac{W}{m\cdot K}$$ | $$\rho$$, $$\frac{kg}{m^3}$$ |
| 20 | 204 | 7500 | ||
| 100 | 11.3 | 41 | ||
| 200 | 12.2 | 40 | ||
| 300 | 12.3 | 38 | ||
| 400 | 36 | |||
| 500 | 35 | |||
| 600 | 14.7 |
Mechanical properties at 20 °C
| Rolling | Standard | Size, mm | Tension | Classifiers | $$\sigma _{U}$$, $$MPa$$ | $$\sigma_{P}$$, $$MPa$$ | $$\epsilon_L$$, % | $$\psi$$, % | $$KCU\cdot 10^{3}$$, $$\frac{J}{m^2}$$ | Treatment |
|---|---|---|---|---|---|---|---|---|---|---|
| Rolling | Standard | Size, mm | Tension | Classifiers | $$\sigma _{U}$$, $$MPa$$ | $$\sigma_{P}$$, $$MPa$$ | $$\epsilon_L$$, % | $$\psi$$, % | $$KCU\cdot 10^{3}$$, $$\frac{J}{m^2}$$ | Treatment |
| Rod | GOST 4543-71 | 25 | 740 | 420 | 11 | 35 | Hardening and tempering | |||
| Forgings | < 100 | 570 | 315 | 17 | 38 | 390 | Normalization | |||
| Forgings | 100–300 | 570 | 315 | 14 | 35 | 340 | Normalization |
Brinell hardness number
| Rolling | Standard | Classifiers | Value, HBW |
|---|---|---|---|
| Rolling | Standard | Classifiers | Value, HBW |
| Alloy | GOST 4543-71 | annealing | 229 |
Technological Properties
Critical point temperatures
Analogues
| USA | Germany |
|---|---|
| USA | Germany |
| 1552 | 1.0913 (50Mn7) |
Standards
| Standard | Description |
|---|---|
| Standard | Description |
| GOST 4543-71 |
Description of chemical elements
Description of physical characteristics
| Parameter | Units of measurement | Description |
|---|---|---|
| Parameter | Units of measurement | Description |
| $$E\cdot 10^{9}$$ | $$MPa$$ | Elastic modulus |
| $$\alpha\cdot 10^{6}$$ | $$K^{-1}$$ | Coefficient of thermal (linear) expansion (range 20°C–T) |
| $$\varkappa$$ | $$\frac{W}{m\cdot K}$$ | Coefficient of thermal conductivity (the heat capacity of the material) |
| $$\rho$$ | $$\frac{kg}{m^3}$$ | The density of the material |
Description of mechanical properties
| Parameter | Units of measurement | Description |
|---|---|---|
| Parameter | Units of measurement | Description |
| $$\sigma _{U}$$ | $$MPa$$ | Ultimate tensile strength |
| $$\sigma_{P}$$ | $$MPa$$ | Proportionality limit |
| $$\epsilon_L$$ | % | Elongation at break (longitudinal) |
| $$\psi$$ | % | Reduction in cross section on fracture |
| $$KCU\cdot 10^{3}$$ | $$\frac{J}{m^2}$$ | Impact toughness |
Designation of types of weldability
| Parameter | Units of measurement | Description |
|---|---|---|
| Parameter | Units of measurement | Description |
| no limits | Welding is performed without heating and without subsequent heat treatment | |
| Boundedly welded | Welding is possible with heating up to 100–120 °C and subsequent heat treatment | |
| Difficult to weld | For obtaining quality welded joints, additional operations are required: heating up to 200–300 °C for welding, heat treatment after welding — annealing | |
| Not applicable for welded structures |